Two Piece Post Base – Used to bolt a post to concrete or other suitable surface.Flat L’s – Used to join other parts of your design.The holes work with an Outside Corner - for the upright, they are aligned, so you can bolt through and make a steel/post/steel sandwich and for the two incoming horizontal posts, the holes are offset so they do not collide. Double Inside Corners – The bottom part of this bracket attaches to the inside corner of an upright post, which then allows each ear on the top part of the bracket to go under horizontal posts coming in from the left and right sides.The holes also line up with our Flat T’s. Bent L’s – Used as an inside corner, either alone or in conjunction with an Outside Corner to make a steel/post/steel sandwich for aesthetics and/or additional strength.The holes line up with the Bent L’s in case you want to use them in making an inside corner on the opposite side of your Flat T. Flat T Brackets – Used to join/attach two incoming horizontal posts which are resting on top of an upright/vertical post.They also work with the Double Inside Corner. The holes line up with Bent L’s if you want to use them on the inside. Outside Corners – Used on outside corners to join/attach two incoming horizontal posts on top of an upright/vertical post. Lifestyle customer photos depict build/use variations only. If you use lag screws, we recommend 1/2″ x a minimum of a 2.5″ long lag bolt, with longer bolts adding more strength. WOOD POSTS AND BOLTS/LAG SCREWS ARE NOT INCLUDED WITH OUR BRACKETS you can pick them up at your local Home Depot/Menard’s/Lowe’s/Ace Hardware store. Our brackets can be installed using any 1/2″ wood lag screws or 1/2″ through-bolts. Optional 6 sets of our Two-Piece Post Bases if you are not setting your posts in concrete.We get a lot of questions about how to build a double pergola (one with six legs) like you may have seen in one of our photos – they use the following: We are the original designer of the PostHugger™ brackets, which may be copied, but never equaled! □ If you find a PostHugger™ knockoff, give us a chance to meet or beat their price. And all our PostHugger™ Brackets & metal artwork products are Made in America with American-Made Steel! We make them using 1/8″ thick steel – a single corner bracket weighs 6 pounds – – strong enough to take what you throw at it (or what you throw it at!), but not so heavy where they are hard to work with. If you want the same thing, but for dimensional 4 x 4 posts, click here.īuild your own rugged and heavy duty PostHugger™ Pergola, Double Pergola, shop/garage/CNC table, or deck with our USA made 1/8″ steel corner brackets!Īlso great for fixing/reinforcing the one you already have! These are not flimsy/bendable metal. These brackets are sold individually and are FOR USE WITH DIMENSIONAL 6 x 6 POSTS (5.5” x 5.5”). NOTE: Fasteners are for mounting to typical 1-1/2" thick lumber.– – For Dimensional 6×6 Posts – – For Dimensional 6×6 Posts – – For Dimensional 6×6 Posts – – ( CLICK HERE ) To go to D-561 "Fastener Kit". NOTE: Install with 3/8” carriage bolts NOT INCLUDED. NOTE: For extra bracket mounting support the D-562 "Rectangular Backing plate" can be added. The sleeve has a 1/2" nut welded to it for the adjustment bolt ( 1/2" bolt included ). with an adjustable sleeve made of 2-5/8" I.D. Angle iron has square holes for mounting with 3/8" Carriage Bolts - NOT INCLUDED. Used in corners were applicable for dual section support or the inside ( underneath dock ) of outside corners to make outside of dock free from dock support pipes. The D-566 "Inside Corner Bracket" features angle iron for better dock mounting support.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |